Bafang M500/M600 Tuning & The BESST Tool

temon10 · Jul 18, 2022

TeoElFeo said:
A question about m500 firmware: what is the difference between the two 10A firmware(2015.5 VS 2050.6). The first one is stock and feels kind of sluggish.. How does the other one compare to it? Currently using 12A and I like the snappiness of it(comparing to 13a) but I would like level1 to be more power efficient - sometimes doing really long rides...

2050.6 ismore powerful and smooth. Last time i used M500 the best for me is 10A 2050.6, now i'm using M510.

temon10 · Jul 18, 2022

Dado said:
Attaching M600 firmware 43V 25A - up to 1300W with 48V battery!!!

->Be careful it is overheating, when u hold full throttle for few mins.
->Throttle has 1s delay when u not pedalling (Bafang what are you doing there!? Was it a purpose? )
->At 20% it shut down and then when I power on motor again it was showing only 1%. (Could be either motor went hard cut off or my battery BMS triped - with no load I measured 39V ) - which is good, as you would drain battery till the end.

So Dado.... if I have M510 43v, and I can run with my 48V battery?

TeoElFeo · Jul 18, 2022

So guys, what's your favourite m500 48v firmware for trail riding? I think I've liked the 12a best out of all due to a good power ramp up(gives power earlier). The only issue I find is that even in PAS1 It's consuming way too much power, especially if you're going over 25-30km/h. Went to try the 2050 which seems more economical but lacks the initial oomph... Any suggestions here?

patdam · Jul 18, 2022

TeoElFeo said:
So guys, what's your favourite m500 48v firmware for trail riding? I think I've liked the 12a best out of all due to a good power ramp up(gives power earlier). The only issue I find is that even in PAS1 It's consuming way too much power, especially if you're going over 25-30km/h. Went to try the 2050 which seems more economical but lacks the initial oomph... Any suggestions here?

i prefer the 12a for my long riding in mountain. perfect for me if i'm alone, a little bit to powerful in 1 (of 5) level if i ride with friends non AE. +- 60% consumed for +- 30km +- 1500 D+, mostly in level 1 and 2.
What you whould mean by "It's consuming way too much power, especially if you're going over 25-30km/h" ? you have over pass the 25 km/h limit (not me) ? in this case it is normal if you consume more, no ?

LAnton · Jul 23, 2022

https://aliexpress.ru/item/1005004391090498.html?_ga=2.150224118.1799115566.1655699927-1027886621.1652866069&sku_id=12000029014513254

LAnton · Jul 23, 2022

LAnton said:
https://aliexpress.ru/item/1005004391090498.html?_ga=2.150224118.1799115566.1655699927-1027886621.1652866069&sku_id=12000029014513254

Video: Usb-кабель Для Программирования Bafang M510 M600 M620,Кабель Для Перепрограммирования Среднего Привода Can-шины,Уникальный Дизайн - Buy Bafang Can Cable,Usb Programming,Bafang M600 M620 Program Product on Alibaba.com

fantic.e-bike · Sep 24, 2022

hello, my name is julien I have a FANTIC ISSMO 45km / h with engine bafang m600 configure with the counter bafang two modes of assisstance are available 'road' and 'hill', it is a valley they have completely bridle since it uses a battery 630w, I would like access to the engineer level in order to unlock the speed limit, can you explain me + in detail with python? Thank you

fantic.e-bike · Sep 24, 2022

Zimmerframe said:
You can download the BESST Tool from there, you then need to contact them to obtain an ID/Password :

BESST

Bafang description

bafang-e.com

They can give you a basic password. But each ID/Password links to their system and has different abilities and can change different things.

hello, my name is julien I have a FANTIC ISSMO 45km / h with engine bafang m600 configure with the counter bafang two modes of assisstance are available 'road' and 'hill', it is a valley they have completely bridle since it uses a battery 630w, I would like access to the engineer level in order to unlock the speed limit, can you explain me + in detail with python? Thank you

mgx · Sep 24, 2022

I advise to stop repeating same question and go to this thread from page1. then read... you will find

Or check this, step by step

Bafang M500/M600 thread

Since this seems to be an interesting motor, why not have a separate topic for it? I'll start with three quotes I have found about the motor on this forum, feel free to add more information that you can find. Over the last couple of days I had heard that there had been reports of the M600...

endless-sphere.com

Script is here

Bafang_M500_M600/BESST at main · OpenSourceEBike/Bafang_M500_M600

Contribute to OpenSourceEBike/Bafang_M500_M600 development by creating an account on GitHub.

github.com

vikino1 · Sep 26, 2022

I'm asking for advice, I have a Besst tool, everything works fine for me, but I can't increase the speed but only decrease it. Is this caused by the Besst tool itself, or is it just a bug in the Python login?

Dado · Sep 26, 2022

Same with me with python script. Theres some region restriction and can set only 25kmh.

You can buy K1 CAN monitor:

K1 CAN Monitor - Bafang CAN speed unlocker - Endless Sphere

mgx · Sep 26, 2022

You need to use old BEST program=1.2.18 works to change limit.

vikino1 · Sep 26, 2022

Použil som to, nefungovalo to.

fantic.e-bike · Oct 1, 2022

mgx said:
I advise to stop repeating same question and go to this thread from page1. then read... you will find

Or check this, step by step

Bafang M500/M600 thread

Since this seems to be an interesting motor, why not have a separate topic for it? I'll start with three quotes I have found about the motor on this forum, feel free to add more information that you can find. Over the last couple of days I had heard that there had been reports of the M600...

endless-sphere.com

Script is here

Bafang_M500_M600/BESST at main · OpenSourceEBike/Bafang_M500_M600

Contribute to OpenSourceEBike/Bafang_M500_M600 development by creating an account on GitHub.

github.com

hello, thank you for your answer and sorry for the duplicate, however if I ask the question it is that one of the steps is failing me, I have never manipulated the codes, suddenly I followed the glass procedure nevertheless when I run the script, there are two lines of writing and .. nothing more and I enter any identifiers in BESST and nothing .. I installed simpleson etc via ms dos command, however, I am precisely independent in the electric but my dealer access limits me to 25km/h while I also sell 45km/h... so I need you guys please, you're the only ones working on it... help me please

vikino1 · Oct 1, 2022

My son started it according to this guide Bestt Python Methode Download the RAR in post No. 8.

fantic.e-bike · Oct 2, 2022

vikino1 said:
My son started it according to this guide Bestt Python Methode Download the RAR in post No. 8.

hello, I come to the news, I finally succeeded in bypassing the login to find myself with the same functionalities as my classic accesses.. the pro script does not work? how to access the engineer version of the software? I use the official interface, does not work on version 1.2.16 .. how can I do? thank you

vikino1 · Oct 2, 2022

I don't understand your post, probably because of Google Translate. I will connect to the display and the controller via Besst. I can't increase the speed but only decrease it. I can change the firmware. Besst worked for me from 2.1.18 up

Slaine · Oct 12, 2022

Hi,

I would like to know why I can't read my paprameter with besst tool pro?
I have a error message
thanks for your help

Slaine · Oct 12, 2022

always me

I would like to update my firmware but I have a failed message after the sound of besst tool
why?

Slaine · Oct 18, 2022

Hi,

any people could help me?
regards

Waynemarlow · Oct 18, 2022

Slaine, as far as I'm aware the M600 firmware is not useable with the BEEST Pro. Only the later revisions of the M510. If you wish to upgrade the Firmware then you will have to use only the original BEEST software.

Waynemarlow · Oct 18, 2022

mgx said:
You need to use old BEST program=1.2.18 works to change limit.

vikino1 · Oct 18, 2022

I have a Besst with which you cannot increase the speed, only decrease it. Can something be done about it?

Slaine · Oct 18, 2022

Waynemarlow said:
Slaine, as far as I'm aware the M600 firmware is not useable with the BEEST Pro. Only the later revisions of the M510. If you wish to upgrade the Firmware then you will have to use only the original BEEST software.

Hi,

thanks for your help.

vikino1 · Oct 18, 2022

Couldn't the Besst tool fw be changed? I think there is such an option in Besst pro.

TeoElFeo · Oct 18, 2022

Yes, but I believe nobody has seen different fw versions for the tool itself. I might be wrong though

vikino1 · Oct 18, 2022

That's why I'm asking, maybe someone can find something that could move the team.

Mida · Nov 10, 2022

krokan said:
Hi, I just update my M500 36v with CRX10NC3615i142017.5-28-2230-20200519-2.bin (Leader Fox stock firmaware) and it is amazing!!
I'm gettting 850w peak. 20A.

I hope that I will not burn out the controller . But as it is stock firmware, should be OK!

Hi,
I also have an M500 engine and would like to flash the firmware to something more powerful.
I currently have CRX10NC3615i142055.8 firmware

Are you still using CRX10NC3615i142017.5-28-2230-20200519-2.bin firmware??
Is everything okay in the long run?
It is interesting that the power is around 18-20A, while the firmware marking is 15A?

thaeber · Nov 10, 2022

Look at GitHub. There is a 17A firmware for 36V available.

krokan · Nov 11, 2022

Mida said:
Hi,
I also have an M500 engine and would like to flash the firmware to something more powerful.
I currently have CRX10NC3615i142055.8 firmware

Are you still using CRX10NC3615i142017.5-28-2230-20200519-2.bin firmware??
Is everything okay in the long run?
It is interesting that the power is around 18-20A, while the firmware marking is 15A?

Yes. I'm still using it and it is great. More than 3000km without any problem.

Bafang M500/M600 Tuning & The BESST Tool

Well-known member

Well-known member

Member

Well-known member

Active member

Active member

New Member

New Member

Active member

Active member

Active member

Active member

Active member

New Member

Active member

New Member

Active member

Member

Member

Member

E*POWAH Master

E*POWAH Master

Active member

Member

Active member

Member

Active member

New Member

Well-known member

Member

Similar threads

EMTB Forums