Bafang m510

[thaeber]

29 front and 27.5 rear. 32T chainwheel and 11-46T 10-spd. cassette. Works flawless.

 

[djol]

Do you know if they sell bafang m510 motor?

They can sometimes source an m510 motor, but they seem still quite limited in supply so often won’t have any in stock. In which case you can usually find one through another seller on Aliexpress.

Re: wheels & chainring: 29ers and 32t for me coupled with a wide-range 10-speed cassette 11-48.

 

[SchadowMaster]

I will buy a Bafang m510 engine. Do you know which cover I should choose?

 

[uef2]

I will buy a Bafang m510 engine. Do you know which cover I should choose?
View attachment 85397

Stuff on right side is for M500, don't know if it fits M510!

 

[uef2]

Stuff on right side is for M500, don't know if it fits M510!

These things are so unstable and break off on the threads. I've already installed the third part. With every slight touch you can be sure that it is defective. You can currently only order via Ali for the price of 25 euros!

 

[uef2]

These things are so unstable and break off on the threads. I've already installed the third part. With every slight touch you can be sure that it is defective. You can currently only order via Ali for the price of 25 euros!

I don't have any options, but a metal version would make perfect sense.

 

[captainhightop]

I don't have any options, but a metal version would make perfect sense.

The problem is, you want it to break away before it pulls the threads out of the bike frame (a metal one would not break, so the frame would!). I'm looking at some sort of TPU or rubber based design, but it's way down on the priority list right now of things to design/print. Plus I wanted to scan the existing one, but my pixel 6 isn't up to the job of photogrammetry and can't justify the cost of a decent 3D scanner to replace a 25 Euro part! Maybe nylon screws so that they would give before hand could be an option too.

 

[uef2]

The problem is, you want it to break away before it pulls the threads out of the bike frame (a metal one would not break, so the frame would!). I'm looking at some sort of TPU or rubber based design, but it's way down on the priority list right now of things to design/print. Plus I wanted to scan the existing one, but my pixel 6 isn't up to the job of photogrammetry and can't justify the cost of a decent 3D scanner to replace a 25 Euro part! Maybe nylon screws so that they would give before hand could be an option too.

Yes, that is probably correct. Metal could damage the frame. Plastic screws are also a good solution, thanks for that!

 

[uef2]

Yes, that is probably correct. Metal could damage the frame. Plastic screws are also a good solution, thanks for that!

 

[uef2]

TPU with a corresponding thickness could also be the solution. Maybe there is someone in the forum who has such opportunities and the STL available

 

[SchadowMaster]

Stuff on right side is for M500, don't know if it fits M510!

Both are compatible with bafang m510, but I don't know which one to choose.

 

[captainhightop]

Both are compatible with bafang m510, but I don't know which one to choose.

The one on the right is the one I chose for the M510, as it matches the E10 frame (2 x holes on side of frame not both sets pointing down like the one on the left)

 

[SchadowMaster]

The one on the right is the one I chose for the M510, as it matches the E10 frame (2 x holes on side of frame not both sets pointing down like the one on the left)

Thanks for helping me

 

[KaroKönig]

Mine finally arrived today

 

[captainhightop]

That's nearly 1Kg lighter than my M600, can't wait to try it out!

 

[Kyokushin]

Nice, 36V 19A.

 

[temon10]

I will buy a Bafang m510 engine. Do you know which cover I should choose?
View attachment 85397

dengfu E10 use the right one.

 

[savas]

hm. so no 48volt?

 

[KaroKönig]

hm. so no 48volt?

Unfortunately no

 

[SchadowMaster]

hm. so no 48volt?

There are 36, 43 and 48 volt.
I bought a 48 volt motor, shipping takes three to four weeks.

 

[uef2]

There are 36, 43 and 48 volt.
I bought a 48 volt motor, shipping takes three to four weeks.

Where do you bought from?

 

[SchadowMaster]

Where do you bought from?

from ali express

 

[SchadowMaster]

Unfortunately no
View attachment 85605

You are likely receiving error code 7 because of over voltage. A 36v battery is actually fully charged when it is at 42.0 volts. But maybe your full battery voltage is higher than that did you check it?

 

[Kyokushin]

47.7V its rather for 43V battery.
Anyway, if you owe 43V battery, just change the firmware in engine to 43V (Bafang need send one to you) and will work.

 

[ficorama]

Unfortunately no
View attachment 85605

wrongly ordered or wrongly sent?

 

[savas]

Hm probably

Unfortunately no
View attachment 85605

probably 11s could work.so you need a new battery.Anyway please share your impressions from the motor.I am planning as well later this year to upgrade to 510

 

[KaroKönig]

wrongly ordered or wrongly sent?

I had selected 48v when ordering and was only asked for wheel-size and thumb throttle. But I think the power output stays the same because the 48v motor has lower amperage.

 

[Kyokushin]

I had selected 48v when ordering and was only asked for wheel-size and thumb throttle. But I think the power output stays the same because the 48v motor has lower amperage.

Only firmware and sticker are different, the hardware is all same.

 

[KaroKönig]

47.7V its rather for 43V battery.
Anyway, if you owe 43V battery, just change the firmware in engine to 43V (Bafang need send one to you) and will work.

I know, had a discharged 50V battery hooked up to test to see when the motor goes into overvoltage protection

 

[ficorama]

I had selected 48v when ordering and was only asked for wheel-size and thumb throttle. But I think the power output stays the same because the 48v motor has lower amperage.

and where did you order from? I ask because I need to get an m510 these days. so that it is not delivered to me wrong. that I don't have to change the battery. i think the power should be equal.