Show us your Whyte bits

[Rahr85]

I need to sort the lower mud guard. I have a good excuse now to clean it all up and sort it tomorrow as the cable ties gave way on the mudhugger today after flying down some stairs. The gap between the two was allowing so much crap to settle on the lower pivot.

 

[Rahr85]

Going to try some 760 wide bars, might need to get a longer stem but recently been running trails where I'm clipping bars.

 

[Mr President]

Going to try some 760 wide bars, might need to get a longer stem but recently been running trails where I'm clipping bars.

View attachment 50828

and you can ride through the door opening too

 

[Tribey]

Rich have a look at this thread E180 RS rear mudguard - EMTB Forums

or this one

Whyte E160RS rear mudguard problems

Hi I have fitted a mudhugger rear mudguard to my Whyte E160Rs but it creates a large gap because of the suspension design. Has anyone else experienced this? Any ideas of any kind of additional deflector I could fit or has anyone tried a different mudguard. I have added an addition deflector on...

www.emtbforums.com

 

[The EMF]

Not ideal but it’s all I had hanging around and its only for the winter anyway. Back part is Mudhigger and the other small bit is rear part of a front defender just slotted in the gap nicely and cable tied at top. Looks shite but then so do mudguards But does the job.

View attachment 50494

Ahh just noticed the bottom protector goes above the upper brace. Nice ?

 

[EebStrider]

or this one

Whyte E160RS rear mudguard problems

Hi I have fitted a mudhugger rear mudguard to my Whyte E160Rs but it creates a large gap because of the suspension design. Has anyone else experienced this? Any ideas of any kind of additional deflector I could fit or has anyone tried a different mudguard. I have added an addition deflector on...

www.emtbforums.com

Not happy with the Heath Robinson job I did the other day, I ordered one of these, trimmed it a bit and it tucks up quite a way inside the mudguard, so should do a good job.

And after making a pigs ear of fitting some helicopter tape on the crank arms, just ordered these off Amazon. They should do the trick.

 

[EebStrider]

Had another go at tidying up the cables......

 

[Rahr85]

as you can see from above i looked at tidying the cables but then realised the only way to truly sort it would be to shorten almost all of them, and ain't nobody got time (skill) for that.

 

[EebStrider]

as you can see from above i looked at tidying the cables but then realised the only way to truly sort it would be to shorten almost all of them, and ain't nobody got time (skill) for that.
View attachment 50961

My cables are the lengths they came from the factory, so it’s quite easy to tidy them up. Until my LBS shortens them for me, it looks a lot better now.

 

[Rahr85]

what you did looks better, i looked at it when i changed the handlebars over but the prospect of sorting it made me want to go find something else to do

 

[Mr President]

 

[Singletrack Scene]

Ours is arriving between 16.00-18.00 today

 

[ERambo]

 

[The EMF]

View attachment 51394

Nothing but rain here on the Northumberland coast, everywhere is up to the nuts in clarts ?

 

[ERambo]

Nothing but rain here on the Northumberland coast, everywhere is up to the nuts in clarts ?

I know how you feel, this was last week before the snow!

 

[The EMF]

Oooooooer.......

 

[EebStrider]

All finished, ready to get filthy!

 

[The EMF]

All finished, ready to get filthy!View attachment 51434

Looks the biz bud ?

 

[Beezerk]

All finished, ready to get filthy!View attachment 51434

Have you named it The Hornet ? ?

 

[Dave.r]

Be interested in what you do to your Zeb. Mine seems to hold itself up in its travel a bit too much at the moment, seems reluctant to get moving on the smaller, repeated hits like small ruts. I'll play with pressure and service the lowers before I start upgrading I think.

Oh, and the TransX dropper lever has got to go IMO! Stiff and can't get it positioned quite right. I have a Loam I'll stick on.

Hi I agree the transX dropper lever is a ball ache, like you cant just position it right, but £60 .00 for a Loam !!

 

[Jamze]

Hi I agree the transX dropper lever is a ball ache, like you cant just position it right, but £60 .00 for a Loam !!

The ZTTO ones you can get on eBay, Aliexpress etc for £15ish might work better. Runs on a bearing and looks like it has more adjustment.

 

[Dave.r]

All finished, ready to get filthy!View attachment 51434

what is that mudguard set up on the rear , Is it effective?

 

[EebStrider]

what is that mudguard set up on the rear , Is it effective?

It’s the RRP Proguard. I’ve not tested it properly yet, but am sure it’ll do the trick. I went for a quick spin round the block, and everything feels really new and tight, so I’m looking forward to everything loosening up. It feels quite heavy, compared to my Cube, which is odd as the CoG is lower on this bike. Maybe it's the tyres??

Here’s a proper pic. Apologies for not lining the tyres up properly! ?

 

[Mr President]

He hung around for a bit, thought I was going to have to set the sag up for him at one point ?.
View attachment 46909

 

[N9VNS]

View attachment 52038

Haha! Robins have good taste in emtb’s too!

 

[Mr President]

Haha! Robins have good taste in emtb’s too!

better balance than me too

 

[Rahr85]

Trying to avoid bottoming out on the rear...

Probably done it wrong but hey ho....

 

[nathdogg]

My E160 RS
I have changed the bars, stem, cranks and the brakes. Still have rear Sram rotor on the bike as I ordered the wrong mount for a 220mm rotor on the back. Loving the bike

 

[Nick790]

1st ride, over the moon.

 

[The Hodge]

View attachment 52247
1st ride, over the moon.

Didn't know the battery had that sort of range ..
Pleased for you ..Great isn't it ! ?