Cassette replacement purchase question

[cazrack]

Hi

I have a Orbea Wild FS H15 2020 and need to replace the worn cassette, the smallest heavy gears are worn out while largest light gears work fine.

Its this bike, but purchased from bikester

2020 Orbea Wild FS H15 E-Bike

It’s time to get moving. Load up your pack for an afternoon ride and start pedaling. Whatever obstacles exist between you and the trails and your Special Places, it’s time to run over them.

www.nrgcycles.co.uk

Cassette is: Sun Race CSMZ80 11-51t 12-Speed Metalic E-bike

SunRace CSMZ800 WA1 Kassett 12-delad 11-51T | bikester.se

SunRace CSMZ800 WA1 Kassett 12-delad 11-51T - till rätt pris! 30 dagars öppet köp och fri retur.SunRace Över 40 000 produkter från 600 varumärken - Bikester.se.

www.bikester.se

Its out of stock but according to the link its compatible with Shimano so can i buy any Shimano 11-51t 12-Speed cassette and it will work or do I need to be careful what to buy?

Thanks for help

 

[salko]

For 12spd Shimano only has 10-51t cassette which uses Microspline freehub, your current cassette seems to have standard Shimano freehub.

 

[Jackware]

Can you order from Amazon UK?

 

[cazrack]

thx for tip, in worst case scenario I can order from UK but its gonna be expensive with brexit.

Do you think this will work? I guess its almost the same.

Kassett SunRace CSMZ90 12 växlar 11-50T silver/svart - Kassetter - Kassetter & Bakdrev - Cykeldelar

www.cykelkraft.se

thanks

 

[salko]

thx for tip, in worst case scenario I can order from UK but its gonna be expensive with brexit.

Do you think this will work? I guess its almost the same.

Kassett SunRace CSMZ90 12 växlar 11-50T silver/svart - Kassetter - Kassetter & Bakdrev - Cykeldelar

www.cykelkraft.se

thanks

This should work.

 

[cazrack]

thanks

This should work.

Thanks I have ordered it.

 

[EnduroDad2k]

Related question: Is it possible to replace just the smallest cog individually? Seems mine started skipping recently.

And anyone know if these 10t cogs in stock anywhere here in the colonies?

Cassette: Shimano CS-M6100-12, 10-51T, 12-speed.

Thanks in advance,
Skippy Long-tooth

 

[DtEW]

Related question: Is it possible to replace just the smallest cog individually? Seems mine started skipping recently.

And anyone know if these 10t cogs in stock anywhere here in the colonies?

Cassette: Shimano CS-M6100-12, 10-51T, 12-speed.

Thanks in advance,
Skippy Long-tooth

It used to be possible, but the pandemic has made it very hard to get your hands on them.

And you can’t just buy the 10T individually; it comes as a set with the 12T. The part number for the set is Y1X498020.

Also FYI, the 14T and 16T can be had individually. The part numbers are Y1X414000 and Y1X416000, respectively. These are somewhat easier to come by.

https://si.shimano.com/pdfs/ev/EV-CS-M9100-4376B.pdf

 

[EnduroDad2k]

It used to be possible, but the pandemic has made it very hard to get your hands on them.

And you can’t just buy the 10T individually; it comes as a set with the 12T. The part number for the set is Y1X498020.

Also FYI, the 14T and 16T can be had individually. The part numbers are Y1X414000 and Y1X416000, respectively. These are somewhat easier to come by.

https://si.shimano.com/pdfs/ev/EV-CS-M9100-4376B.pdf

Thanks very much for the info!

 

[StevoKickstart]

Thanks very much for the info!

Hi,

What was the outcome of this? did you manage to replace the smaller cogs?

I'm asking as I am in the same situation; I've worn the smallest 2 cogs in 350 miles !!!!!!!!!! not good enough I think...

 

[cazrack]

Hi,

What was the outcome of this? did you manage to replace the smaller cogs?

I'm asking as I am in the same situation; I've worn the smallest 2 cogs in 350 miles !!!!!!!!!! not good enough I think...

Hi

I replaced the whole cassette since almost all cogs where bad, it works great now.

 

[S13]

FWIW, you can buy the sprockets on Ali too. Just search for "M8100 sprocket" and you will get some hits. Ive ordered from 0086bike Store and Chaser Store in the past without problems.
The small sprockets are interchangeable between M6100, M7100 and M8100.