Avinox M2s rattle

⚡ EMTB Pro Go Pro — exclusive discounts & ad-free Peaty's 25% off & more · Ad-free browsing · Pro badge See the deals →
Does the rattle happen in all gears or only the small cogs like 8th to 12. The sound is very very similar to a derailleur that has a clutch that is a bit loose and causes a rattle.
 
How concerned should a potential new Meyer be about the rattle on the MS2? I’m a casual weekend Warrior riding 8 to 12 miles each Saturday and Sunday on flat trails in South Florida no real climbing just punchy, black diamonds, switchback, etc. 225lb so a little heavier than normal riders.

I was considering the PR carbon, Ari wire peak 3.0, propain ekano 3 and teewing.. prefer a mullet set up. All the rattle noises are a little concerning… I wonder if I should just switch to the Bosch maybe the SC Vala? I also worry a little bit about Support with all these bikes not having a huge US presence.
I was bored and asked ChatGPT to count the no of unique users in this thread that had rattle issues, it counted 10. Given this thread is the top result on Google for M2S rattle and Rob's "testimony", I wouldn't worry too much for an average e-MTB buyer.
 
I was bored and asked ChatGPT to count the no of unique users in this thread that had rattle issues, it counted 10. Given this thread is the top result on Google for M2S rattle and Rob's "testimony", I wouldn't worry too much for an average e-MTB buyer.
It’s only been 2 months since release. Reading this thread, I thought there were maybe 3–4 cases, but 10 is a freakishly high number for such a short period of time.

I was curious about the newcoming Wild with the M2S motor, but Bosch Gen 5 is probably the safer bet.
 
So no one been in contact with dji/avinox regarding the rattle?
So just got a call his morning and my M2S motor has been accepted for warranty, here is what it sounds like in the stand not under any load.

350 miles on the motor, Amflow have said keep on using it until the replacement motor arrives.

 
Last edited:
So for me this is absolutely not a rattle issue, it's something else.

Here is the rasping noise when under load in normal riding conditions.


Looking forward to the motor being replaced, apparently it will be around 2 weeks for the new unit to arrive.

Hopefully this is a 'batch' issue and nothing else.

For me I still love the bike and having rode with other people on selection of motors, this is still quieter than most even with the fault.
 
Aren't you all cherry picking, to notice that Motor rattle?

Between trail noise (Tires/Wheels, Chain Slap, due to rocks and roots), plus the brake noise (not the squicky sound, but yet the Brake Pads rubbing while braking), the suspension noise (hydraulic), and you still notice motor rattle?

Having a CX4, I found the M1 seriously silent!
And after all miles using the CX4, I start not earing my motor rattle, but can notice imediatly any issues (like a loose chain guide).

What were your last ebike motor? Was it more silent that Avinox?
 
Aren't you all cherry picking, to notice that Motor rattle?

Between trail noise (Tires/Wheels, Chain Slap, due to rocks and roots), plus the brake noise (not the squicky sound, but yet the Brake Pads rubbing while braking), the suspension noise (hydraulic), and you still notice motor rattle?

Having a CX4, I found the M1 seriously silent!
And after all miles using the CX4, I start not earing my motor rattle, but can notice imediatly any issues (like a loose chain guide).

What were your last ebike motor? Was it more silent that Avinox?
I don't have motor rattle, my issue is different.

My personal experience is limited as this is my first ebike, however even with this rasping issue (that Amflow want to investigate and have warrantied) other motors are a lot noisier :unsure:

trail chatter does over ride any noise when going downhill, I can hear the Magura brake pads more than anything.
 
Does the rattle happen in all gears or only the small cogs like 8th to 12. The sound is very very similar to a derailleur that has a clutch that is a bit loose and causes a rattle.
I will check, and yes you are right, because I change a sprocket to 36, and setup the derailleur on 7th cog (red) and I have to setup on 6th (my mistake). Then I will check the rattle...
 
10 is a freakishly high number for such a short period of time.
With the recent verified, raspy motor that didn't rattle how many actually confirmed issues are there. One recent rattle complaint sounds like a dodgy derailleur and is yet to be determined .
 
We will need 6+ months and hundreds of M2s' being over 750 kms to know if there is any pattern at all. At this point, it's worth noting but probably not worth worrying about too much. If you want an Avinox, buy an Avinox.
 
Aren't you all cherry picking, to notice that Motor rattle?

Between trail noise (Tires/Wheels, Chain Slap, due to rocks and roots), plus the brake noise (not the squicky sound, but yet the Brake Pads rubbing while braking), the suspension noise (hydraulic), and you still notice motor rattle?

Having a CX4, I found the M1 seriously silent!
And after all miles using the CX4, I start not earing my motor rattle, but can notice imediatly any issues (like a loose chain guide).

What were your last ebike motor? Was it more silent that Avinox?
Cherry picking, no. Aside from this motor rattle, the bike is near silent going over bumps. There is no chain slap, there is no suspension rattle or clunking, there is no cable chatter and there shouldn't be any noise aside from tire and cassette. So when the motor makes a medium frequency clicking which reverberates through the carbon frame, it's quite annoying. Even more so when the manufacture used the silent nature of this motor as a selling point.
 
Keep reading
    Browse all

    Similar Threads

    Community Stats

    Since 2018
    669K
    Messages
    40,997
    Members
    Join 30,000+ Riders, it's free!
    Back
    Top