Bosch Gen 5 Rumour - More Power updates coming!

Status
Not open for further replies.
i just did mine and i had to uninstal and install the app again.
 
⚡ EMTB Pro Go Pro — exclusive discounts & ad-free Peaty's 25% off & more · Ad-free browsing · Pro badge See the deals →
I tried on my iPad and still no luck. Guess I will have to wait the 24 hours. I am hoping it comes live this afternoon since I have been out of town and almost a week of no riding
 
From a different thread, this info was good. I don’t know if it’s required to delete the app and reinstall but the key was going into the components and installing an update there for the extra torque.


For those not seeing any change. Delete and reinstall flow app, then go to components, drive unit and you should see the next phase (20 second) update to get the actual adjustment installed…faff, my kid could vibe code something better than this, but at least it works
 
Junior said:
I tried on my iPad and still no luck. Guess I will have to wait the 24 hours. I am hoping it comes live this afternoon since I have been out of town and almost a week of no riding
Click to expand...
If you have installed firmware update successfully and waiting for banner (24h window) - you just need to uninstall and install Flow app again and banner should pop up
 
PeterHenric said:
From a different thread, this info was good. I don’t know if it’s required to delete the app and reinstall but the key was going into the components and installing an update there for the extra torque.


For those not seeing any change. Delete and reinstall flow app, then go to components, drive unit and you should see the next phase (20 second) update to get the actual adjustment installed…faff, my kid could vibe code something better than this, but at least it works
Click to expand...
Ill have to try this. I am at 5 uninstall and reinstalls. Not seeing any new updates when I check, but I have not done it through the components.
 
Junior said:
Ill have to try this. I am at 5 uninstall and reinstalls. Not seeing any new updates when I check, but I have not done it through the components.
Click to expand...
When you say you don’t see any new updates, are you referring to the main update? This is actually a 2 step update process. First is the main software then you have to go into the drive unit and do another little update there. On my bike, the new update showed up right away. Didn’t take any special stuff. It was the second step that is eluding most people because it isn’t intuitive.
 
russ_e said:
I'm on about my 20th attempt (at least).
Click to expand...
I’m wondering if Pivot has not approved this update. I’d be pretty frustrated by that if they are trying to promote the new bike. Mine is only 3 months old. Currently on a 2025 Shuttle AM
IMG_4763.webp
IMG_4764.webp
 
claudiobosticco said:
so is Avinox not compliant in Germany?
Click to expand...

I don't think that's "law" yet in Germany or EU... the 600% to 15KPH one of among a few "recommendations" ZIV [German Bicycle Industry] is pushing regulators towards.

Bosch stated in their recent Performance 2.0 press camp their motors are complaint with "current" and "future" regulations and since the CEO of Bosch is part of the ZIV group... he may have some insight to pending regulation or what they are pushing for.
 
PeterHenric said:
When you say you don’t see any new updates, are you referring to the main update? This is actually a 2 step update process. First is the main software then you have to go into the drive unit and do another little update there. On my bike, the new update showed up right away. Didn’t take any special stuff. It was the second step that is eluding most people because it isn’t intuitive.
Click to expand...
I was able to install the main update first thing this morning. I am wondering if anyone has screenshots of how to do the drive unit update? I am thinking Pivot has not approved the update yet which is kind of frustrating. I need to call pivot, but they still haven't responded to my previous message, which was completely unrelated
 
Anyone who has completed the update, can you check the software version on the motor when you go into the individual components?
 
Junior said:
I’m wondering if Pivot has not approved this update. I’d be pretty frustrated by that if they are trying to promote the new bike. Mine is only 3 months old. Currently on a 2025 Shuttle AM
Click to expand...
I think it is much more likely the update has simply not yet rolled out in your area. I'm not seeing it yet on either my Gen 5 or Gen 4 bikes which is typical, normally don't get them for 1 or 2 days later here in Germany! I can't believe in my case that the manufacturer would block the update for the Gen 4 bike since max. power will remain at 85NM
 
bmwpowere36m3 said:
Dude's have zero patience... been speculating for months about update, lmao. Prolly faster to buy an Avinox bike.
Click to expand...
Sorry for being excited about a free update for our bikes. I am happy with the existing power, but can you blame us for wanting the new update?

Do you get joy from dissing strangers on the internet?
 
Joecrow said:
I think it is much more likely the update has simply not yet rolled out in your area. I'm not seeing it yet on either my Gen 5 or Gen 4 bikes which is typical, normally don't get them for 1 or 2 days later here in Germany! I can't believe in my case that the manufacturer would block the update for the Gen 4 bike since max. power will remain at 85NM
Click to expand...
Maybe so. I find it interesting that the main software update was released, but not the power. The update I installed very clearly stated it was the 120nm update. Oh well
 
Junior said:
Anyone who has completed the update, can you check the software version on the motor when you go into the individual components?
Click to expand...
I believe the update popped up on my main page of the Flow app. If it wasn’t there, I had to click on the settings icon in the upper right hand corner of the screen.
IMG_5812.webp


Then from there you click on the components and then the drive unit. It showed an update there as well.
IMG_5811.webp


These are the software versions on my bike now.
IMG_5810.webp
 
PeterHenric said:
I believe the update popped up on my main page of the Flow app. If it wasn’t there, I had to click on the settings icon in the upper right hand corner of the screen.
View attachment 183808

Then from there you click on the components and then the drive unit. It showed an update there as well.
View attachment 183809

These are the software versions on my bike now.
View attachment 183810
Click to expand...
Thanks for that! I managed to get that update banner on the main screen after updating the app this morning. Installed it, and no change in the ability to adjust the power. Guess I will have to be patient. Have you looked into customizing the settings and are actually able to move it to 120 nm?
 
Junior said:
Thanks for that! I managed to get that update banner on the main screen after updating the app this morning. Installed it, and no change in the ability to adjust the power. Guess I will have to be patient. Have you looked into customizing the settings and are actually able to move it to 120 nm?
Click to expand...
It is not necessary to uninstall the Flow app. It is enough to clear the cache and app data for the Flow application.
 
Junior said:
Thanks for that! I managed to get that update banner on the main screen after updating the app this morning. Installed it, and no change in the ability to adjust the power. Guess I will have to be patient. Have you looked into customizing the settings and are actually able to move it to 120 nm?
Click to expand...
I did see that option. I didn’t actually adjust it but it did say it was possible.
 
killerade said:
It is not necessary to uninstall the Flow app. It is enough to clear the cache and app data for the Flow application.
Click to expand...
I do not see a place to clear cache on an iphone. Seems to be uninstalling/reinstalling is the process for this.

On another note, has anyone been able to connect their garmin to the bike? I quickly tried through the typical Garmin connection process, but all it showed was lights to connect to.
 
I also had to remove and reinstall flow app, to proceed w update under components - drive unit. Now got the 120nm
What about extended boost? That’s still missing..
 

Saw this on facebook. I definitely do not have that banner in the motor settings. I also noticed it said to connect all the components before doing the initial update. I probably did not have my mini controller connected at that time. Ill wait til later to see if it works, but deleting and reinstalling the app has been done more than I would like to admit
 
CaRaBeeN said:
I also had to remove and reinstall flow app, to proceed w update under components - drive unit. Now got the 120nm
What about extended boost? That’s still missing..
Click to expand...
Oh it’s already mentioned in the anouncement today that it will be released for customization in mid-2026
 
Status
Not open for further replies.
Keep reading
    Browse all

    Similar Threads

    Community Stats

    Since 2018
    669K
    Messages
    40,837
    Members
    Join 30,000+ Riders, it's free!
    Back
    Top