Search results for query: *

Has any one had a cadence sensor not working properly warning on a Bosch Gen 4 motor. The warning came up on the Purion 200 mid ride to check the Flo app. I restarted ……off on a couple of times and it stayed on. The power was down when the error was showing. Another reboot and wiped the magnet...

Does anyone have a bearing size or code for front wheel bearings on an e160RSX MY 2022. They are the standard / original DT Swiss hubs.

Has anyone got a jacket that is really waterproof? I have a less than one year old Endura MT500 jacket and although I have worn it quite a bit it hasn't been in soaking rain that much. That changed on the last two rides and I have been completely soaked. When I got home I layed it down and...

I have stripped my DT Swiss ratchet XD free hub as it was noisy. It's a standard e160RSX V1. I have cleaned and re-greased it and everything seemed ok but I can't get the cassette to seat fully on the splines of the driver. It seems to be on and tightens to the correct torque but the end cap is...

Does anyone know if there is a special chain checker for the flat top chains ?

My RSX 160 with Purion 200 turns off immediately after turning on. I get the Bosch Purion 200 screen then it turns off. Has anyone had this or any suggestions.

Has anyone had problems with glazed pads? After cleaning and sanding they still glaze. Are some pad compounds more susceptible than others?

Does anyone know if anything is missing here. The T type cassette is torqued down but will just lift out probable taking the XD free hub with it. Is there a cap missing or is this normal? It works ok.

Has anyone replaced spokes om a DT Swiss rim ? Are the spokes at each side, going to hub side or disc side, different lengths ?

Has anyone dropped the motor on an e160 RSX to replace hoses / cables. Do you undo the Torx T40+ on both sides ?

I have upgraded to a SRAM AXS T set up a while ago. Is the cassette the same as the 10-52 AXS with a hanger ?

I've bought a lot from Wiggle and CRC in the past..the go to really inc the 12%, and they sent Haribos that my wife liked. Anyone got a go to alternative, in the UK ?

My front wheel seemed to be buckled It felt ok but when riding it looked wobbly. I tried a self test with a pencil on the forks and the rim looked true. It was still the same so I took it to a lbs ( in France). They said the rim was ok but it was the tyre (Maxis Assengai) that made it...

Hi All My e160 RSX has a UDH deraileur hanger. The bolt to the frame is a left handed thread. Can anyone confirm that the bolt from deraileur to the hanger itself is right hand or left hand thread It seems very tight and I don't want to try too hard the wrong way. Thanks

I have a 1 yr old Whyte e160 RSX with a Bosch CX gen 4 motor. When I haven’t ridden for maybe a week I get the bike ready and just ride it round the garden to check everything. The controller is in Eco with a green light. After a couple of mins riding the light turns orange and stays orange...

Has anyone upgraded to the newSRAM T type group set ? Any opinions / comments?

I have to top up a Stan’s fluid tyre on a bike in France. I won’t be able to take Stan’s (flying) and I am not sure it will be available. Does anyone know what I should be looking for that will mix ?

It seems as though you need the whole group set for this set up as the cassette, chainring and chain are different. Does anyone know if there Is there any reason why you can’t still use the 155mm Hope cranks?

Has anyone had an unresponsive AXS GX. It just stopped responding mid-ride. The battery was fully charged before the ride. I re-charged it when I got back until the charger light went green but still no response. It doesn't flash when pressing the derailleur. I changed the controller battery...

Does anyone know what may have caused these gouges in my frame / swinging arm. These pictures are from underneath and I haven't noticed them before so I don't know when they happened. They are on both sides marked in red. I can feel them they are deeper than paint scratches.