Search results for query: *

Has anyone got an original plug in Avinox headlight and mounting parts they would like to sell. Now that the Avinox bikes come with the headlight included, and not everyone will use it, I thought I'd ask.

This happened to me as well. My bike never used to rattle at all but suddenly developed a 'motor' rattle at about 500miles. Shortly after this the speed sensor packed in. It came back from the speed sensor repair rattle free again, the same as it used to be.

It should only change each time you tap the upper right corner. With each tap on the screen it will alternate between %- km-%-km. It should stay on what the last tap of the upper right corner left it on. I sometimes find mine on the guessometer when I have been cleaning the screen and...

The shop tested mine by substitution, my original speed sensor tested ok on a different bike and my original motor gave the same error with a new speed sensor. I suspect the sensor cables may be breaking on the motor side of the junction but thats just a guess. My motor hasn't been near water...

I had the same problem with speed sensor error. I took it to the bike shop 7 days ago and received it back today with a new motor fitted. Superb service from Amflow/ DJI. The only problem I have now is my bike seems to be stuck in EU. I can't seem to get it to go back to Latvia 🤔

The plastic on mine crumbled around the screw holes as well. Seems like somethings not right with the plastic.

Can't find anyone to send one to the UK either unless you order 300 of them from Higo. I'm almost ready to cut the plug off the back of the display and solder in a more readily available connector.

Thanks, Vadll, I thought that might be the case.

Yes, I have had it running on my ep8 in US mode for a few years now. I was asking if the new update would unlock cat3 45km/ hr on the ep8.

Does this work on EP8 as well, or just EP801?

The extender powers the motor directly through the charge port sharing the load with the main battery. The bike software won't allow the extender to charge the main battery and will throw an error if it tries. The extender should have electronics to stop the main pack charging the extender. The...

Or 3D print a tight fitting plug. I was going to bolt mine in place but now thinking of removing the bolt holes and gluing it in place, maybe with silicon.

No rattle at all on mine until it went in to my local bike shop for a new speed sensor under warranty at 8months/ 1000miles old. It came back sounding nearly as bad as my ep8 powered Orbea Rise. I suspect it's cable rattle in the downtube above the motor but haven't been arsed to drop the motor...

Auto and Trail both vary the assistance depending on input power/torque as well as inclination of the bike and speed etc. The main difference is Trail can be set up to give more assistance than Auto. On a down hill to uphill transition you can feel the power ramp up significantly as the...

DIY

Amflow PL carbon Pro (med) with Avinox M1 motor 800Wh battery plus 400Wh range extender (1200Wh total) Bike weight 20.6kg plus 1720g range extender Bike travel 160/ 150mm I'm 82kg +2kg backpack Tyres Magic Mary pro and Albert pro, both Ultra soft radial trail casing. Trail conditions soft but...

Yes, I was referring to the cracks from the corners of the knock-block slot. The point I was trying to make is that the areas highlighted by Amflow look like the areas of hi/lo and or filler which you can see on my pictures.

That's why I took the pictures, I was shocked at the finish to be honest. The bottom cup is just as bad, I've now managed to upload the second picture which wouldn't send until downsized it.

I regreased my headset bearings, during routine maintenance, at the weekend and noticed the cups in my frame have a lot of filler and are pretty uneven. They also show obvious signs of reworking/ manual dressing. They look similar to yours except without the cracks as far as I can see. This is...

Have you powered the bike on before trying to set the limit?