Search results for query: *

Bars have printed on indicator marks of rotation, with 0 deg aligned with horizontal on my bike, if anythig 0-deg-mark is pointing a few deg upwards from horizontal. The angle you have on the bars in your printout, where does it origine from ?

Agree to disagree, My riser bar has a vertical rise of 70mm on a -50mm stem on 63deg headtube angle. Center of grips is -40..-50mm behind center of steerer tube.

Get the geometry dialed before you commit to a new bike , measure your RAD and how far your bike setup is matching your body RAD. 490reach looks long compared to 172cm height. Try reversing the stem on current bike, with the high rise bar it will compensate for the "long reverserd" stem...

Hi @Greg , pleace list service providers for remote diagnostics of bosch motor systems

310 reach to grips I am mire like 50..55mm behind center og steerer tube to grips. Combination of -50stem and 70rise is equal to -15 stem and 0 rise 🥳

Well, don't want to spend 8k on a test mule, use what I have and buy the cheapest parts needed to get the geometry right and get going :cool: 850Euro used so far. But it is quiet :sick: to look down at a -50 stem :ROFLMAO: Reversed arc fork and reverse stem are a bit mind cracking. ...it...

467 CS / 502 Reach / 173cm / RAD 836 at 63,4deg 23cm steeret tube, -50 stem +70 rise Grips 30-40mm behind center

Intend 25mm stem, love the front end control, full blown test mule w 474 chainstay and 502 reach in the making.

Hi, What motor systems can you get up and running without a workshop software or frame number serial ? Many motors, controllers and hardness is available, online but what can be used by DIY Bosch? (yes, some ebay sellers sell new ready to run motors) Used motors can be used if bought with a...

It is possible to push the bearing through, the ring. I could not loosen mine, even after several attempts with heating the hub

Knock axle out from driver side. Did finish mine today. 6902 bearings

Hi, did you figure this out? I am having some issues with how to remove the axle

This is a 2022 colour bike

There is a huge difference btw std Fox38 and E-tunned Fox38, E-tunnued is way softer on the damper site (valved for comfort), while many run the compression on the std Fox38 fully open.

The 800wh is quiet stiff to push out, so packed that my 800 battery had ruptured plastic and almost shortcircuit two wires to casing from factory (rupture in oposite direction of the way I pushed it out) Get something like a pice of wood in similar shape as the inside og casing, use sope spray...

To be more accurate : S-works framekit I bought 4.500€. Reign e+1 2024 was discounted 30% 5.600€ [S-works om sale (complete) 8.000€] I had most parts for complete build using the frame set, (using Giant E TRX wheels from my Old Reign) So total cost would be c.a. the same. …for me ;)

I have switched from Reign E+, to Levo Sworks. Giant motor power at low cadense is better, S-works was same price as heavily discounted Rein E+1 2024, I needed one size smaller,, Giant did not want to sell frame only. But for racing Yamaha needs to do some updates. else I would have chosen the...

Saturn 16 - Small is simular to most brands Large. And I need XS, but its not available😭

Agree, only BMS gets a bit hot during charging, electroninc board is packed in plastic, the two boards are in a sandwich, covered in thick silicone , endcover is plastic. So no part of BMS is designed to dissepate heat efficently

No issues. Removes 600gr weight Brand new battery, has about 900km on it now. Plastic/carbon case to save weight. Yes Mods often void warranty. If you would look inside your battery, you can see how the battery cells are packed in plastic casing. Plastic has ok thermal conductivety