Hi!
I have a 2026 wild and have just updated to the latest version that supports up to 120nm on the bosch gen 5. 750wh battery.
However only 100nm are selectable. I read in the update docs that you require the 600wh or 800wh battery or the extended battery?
Have you tried with only the 750wh...
Hi!
Today I just noticed that my Bosch Line CX gen5 motor does some "electronic noise" when I stop after some seconds or minutes or riding. It sounds to me like a "fan noise" and then it stops after some seconds.
What is it? Thanks!
Video of the Noise: It sounds for a few seconds after the...
Hi!
Today I have just picked up my new orbea 2026 M-TEAM. Very nice and powerful ebike. However I cannot activate the eshift function.
There is a "components" section on the settings of the kiox 400c device that shows eshift as available, and the current gear used is shown on the display, but...
Hi!
Can you please tell me your opinion about these two bikes? Orbea Wild 2025 vs Turbo Levo 4 Comp
Now that you can upgrade the orbea wild to 750W and 100nm Motor, which one would you choose and why?
Thanks!!!
Hi!
Sorry to ask again about sizes, but I have just tried the S4 for my 186cm height and I feel like I need more distance to the handlebar.
Should I go for the S5 or just increase 2-3cm the stem?
Thanks!!!
Hi!
My ep8 rs motor has developed play and noises... is it possible to replace it with a normal shimano ep8? There are some cheap motors on ebay and aliexpress.
Thanks!
Hi!
I have a small problem where the battery reaches 99% and then it takes forever to get to 100% (sometimes it never reaches it). I have measured the output of the charger and it reads 41.3V instead of the 41.8V it should.
Can you please measure yours and tell me the readings to know if mine...
Hi!
I have a weird noise when pedaling (motor off) on my giant syncdrive pro motor (pw-x). Can you please review my video and tell me if you know what I could do? The exact position of the noise changes if I move the pedal position (backpedaling). Thanks...
Hi!
I got my 625wh battery replaced recently and when charging in the bike, the charger never ends. It is always blinking green. After 5-6 hours I disconnect it and it is always somewhere between 95% and 99% (never 100%).
I have tried once to charge it outside the bike and it reached fixed...
Hi! I have a 625wh battery that shuts down when using high asistance levels. At the beginning is working fine, but when using 3+ assistance level for some time it shuts down. Then it will shut down even using level 1 until you let it rest for some hours.
Can it be repaired? Do you know of any...
Hi!
Today's ride was a total disaster. It is hot here but not much more than other days or years I have ridden this bike.
Anyway, when asking more power to the motor, the bike suddenly went off. Level 3 on some climbing or level 5 on flat terrain, it went off. I was able to switch it on again...
Hi!
My orbea rise with ep8 rs has developed a new noise, especially noticeable when the chainring goes backwards (moving the wheel backwards or rotating the chainring manually as seen in my video below, as pedaling backwards does not move the chainring).
To me it sounds like a bearing...
Hi,
Today I just noticed a new noise from the motor area when moving the rear wheel backwards (making the chainring move backwards also).
Please take a listen to these videos and let me know what you think. I have just got the bike back because a fork repairing so this is becoming very...
Hey! Do you know where to buy replacement motor mounting bolts for my syncdrive pro motor? (pw-x 2019).
Can't find anywhere and I need to replace of them, Thanks!
Hi!
I have just received my orbea rise range extender and while installing I noticed the manual says to use 5nm of torque for the bolts.
I tried that without noticing the battery support is all plastic and has no metal inserts or reinforcements. Before reaching the 5nm I noticed the screw had...
Hi!
I had a syncdrive sport motor on my fathom e+2 2019 and it was an 80nm motor...
I am about to buy a new 2021 fathom e+1 with sport motor but it says 70nm only...
have they reduced the power of this motor? Why?
thanks
Hi!
Do you know if it is possible to replace the syncdrive pro motor from 2019 (pw-x) with the new pro motor from giant (pw-x2 based)?
I think the geometry is exactly the same and the mounting bolts are in the same place. I have already upgraded the ride control one unit with the 2020 one and...
Hi!
my orbea rise came with the ew-en100 only and I would like to add a display. I know the sc-em800 is the one to get, but it requires sd300 cables.
I have seen some builds with ep8 and e7000 display... and using sd50 cables. Could I just install this display? Any other option with ant/ble...
Hi!
can you please tell me if the sc-em800 display (the one for the ep8 motor) has an available light port to connect an ebike light? Do you know how many volts?
If you have this display, could you please share a picture of the back with the connectors?
thanks!!!