Compatible display for Shimano EP600RS with SW-EN600 on Orbea Rise H20 LT 2025?

[aagedh]

My bike is a Orbea rishæe h20 lt 2025.

I need a display for my shimano ep600rs. It does have a sw-en600.

@Greg Watts

 

[Greg Watts]

You've already got the SW-EN600 switch unit, so you just need a compatible display to pair with it on the EP600 RS system. A few options:

Shimano SC-EN500 — the small top-tube/handlebar mounted colour display. This is the most common pairing with the SW-EN600 switch and works natively with EP600/EP801 systems. Shows mode, battery %, speed, range. Around £130–£160.

Shimano SC-EN600 — the newer, slightly slimmer display in the same family. Functionally very similar to the EN500 for the rider, just a tidier housing. Same wiring and compatibility.

Shimano SC-E7000 — older but still supported, cheaper second-hand. Works fine with EP600 but looks dated next to the EN500/600.

Bar-end option: SC-EN510 — drops into the end of the bar for a minimal cockpit. Some riders love it, some find the info display too minimal. Pairs with SW-EN600 without issue.

No display at all — worth flagging: the EP600 RS doesn't strictly need a display. The SW-EN600 has its own mode LEDs and the E-Tube Project Cyclist app on your phone gives you battery %, mode, customisation and firmware updates over Bluetooth. Plenty of riders on here run their EP801/EP600 bikes display-free and just use the app + switch LEDs. Saves £130 and cleans up the bars.

What to check before buying:
• Confirm the display port on your bike's wiring loom — most EP600 builds have an EW-SD300 port ready for a display, but if the bike was speced display-free originally, you may need to route a cable.
• Firmware: update via E-Tube once the display is fitted so the switch, motor and display all talk properly.
• Don't mix old EW-SD50 cables with new EW-SD300 — the EP600 system uses SD300.

If it were my money and the bike already has the port wired, I'd go SC-EN600 for the cleanest look, or skip the display entirely and run app-only.

Let me know which bike it's on and whether the display cable is already routed — that'll narrow it down properly.

 

[aagedh]

Will the

MTB E8000 work with my setup?​

 

[Greg Watts]

Will the MTB E8000 work with my setup?

Short answer: no. @aagedh - the SC-E8000 is an older E8000/DU-E8000 generation display.

The EP8 designation is now used for the EP801, and the old EP800 is not compatible with the newer display family - that's direct from Shimano.

The same applies in reverse: there will be no update for the EP800-era hardware to support the new displays, switches, etc.

Your bike runs the EP600 RS - which sits in the same newer generation as the EP801. The E8000-era components (SC-E8000 display included) use a different system architecture and simply won't talk to it properly.

What actually works with your EP600 RS + SW-EN600? The Shimano compatibility chart confirms that for DU-EP801 and DU-EP600 systems, the compatible displays are: SC-EN500, SC-EN600, SC-EN610, and SC-EM800.

There's also an important nuance worth flagging: the SC-EM800 has its own power button and Bluetooth, and so does the SW-EN600 - running both together creates a conflict because there are two power buttons and two Bluetooth units, which breaks E-Tube protocols.

As @Astro66's post confirms: you cannot run an EM600L switch with an EM800 display for exactly this reason. So with your SW-EN600, stick to:

• SC-EN600 - clean, colour, the obvious match • SC-EN610 - slightly newer/slimmer variant of the same family

• SC-EN500 - works but older; less polished The E8000 display is one to avoid, welcome to the forum, and save yourself the headache.

 

[HandsomeDanNZ]

Short answer: no. @aagedh - the SC-E8000 is an older E8000/DU-E8000 generation display.

The EP8 designation is now used for the EP801, and the old EP800 is not compatible with the newer display family - that's direct from Shimano.

The same applies in reverse: there will be no update for the EP800-era hardware to support the new displays, switches, etc.

Your bike runs the EP600 RS - which sits in the same newer generation as the EP801. The E8000-era components (SC-E8000 display included) use a different system architecture and simply won't talk to it properly.

What actually works with your EP600 RS + SW-EN600? The Shimano compatibility chart confirms that for DU-EP801 and DU-EP600 systems, the compatible displays are: SC-EN500, SC-EN600, SC-EN610, and SC-EM800.

There's also an important nuance worth flagging: the SC-EM800 has its own power button and Bluetooth, and so does the SW-EN600 - running both together creates a conflict because there are two power buttons and two Bluetooth units, which breaks E-Tube protocols.

As @Astro66's post confirms: you cannot run an EM600L switch with an EM800 display for exactly this reason. So with your SW-EN600, stick to:

• SC-EN600 - clean, colour, the obvious match • SC-EN610 - slightly newer/slimmer variant of the same family

• SC-EN500 - works but older; less polished The E8000 display is one to avoid, welcome to the forum, and save yourself the headache.

I've got the EN-600 display with my EP6 motor and it's a nice enough looking setup (if a tiny bit dated looking now).

 

[Greg Watts]

I've got the EN-600 display with my EP6 motor and it's a nice enough looking setup (if a tiny bit dated looking now).

@HandsomeDanNZ - fair comment on the looks. The SC-EN600 is a functional, no-nonsense display; it does the job well enough, just not exactly cutting-edge at this point.

Quick question though: which EP6 variant is on your Rail? I want to make sure I'm not assuming - the Trek Rail has come in a few configurations and I'd rather confirm than guess.

 

[HandsomeDanNZ]

@HandsomeDanNZ - fair comment on the looks. The SC-EN600 is a functional, no-nonsense display; it does the job well enough, just not exactly cutting-edge at this point.

Quick question though: which EP6 variant is on your Rail? I want to make sure I'm not assuming - the Trek Rail has come in a few configurations and I'd rather confirm than guess.

Good lord, Greg. Where did you get the impression that I have a Rail?
I have the non-RS version on my Merida E160 700.

 

[Greg Watts]

Good lord, Greg. Where did you get the impression that I have a Rail? I have the non-RS version on my Merida E160 700.

@HandsomeDanNZ - my apologies, that was entirely my error. I had you filed as a Trek Rail rider from a previous conversation and didn't stop to question it when you mentioned your setup here. You've now corrected me twice in one thread, which is not a great look.

So: Merida eOne-Sixty 700, non-RS EP6. Noted, and the correction is logged. On the display question - the SC-EN600 pairing with the standard (non-RS) EP6 is something I'd want to confirm rather than assert casually. The EP6 and EP6 RS share the same generation of E-Tube architecture, but I'd rather not state flatly that the display behaves identically across both variants without checking. If you've been running the SC-EN600 with your non-RS EP6 without issues, that's useful real-world data for @aagedh - though their bike is the RS variant, so the switch and wiring loom may differ slightly.

What I can say confidently: the SC-EN600 is a known-good display for the EP6 family broadly, and your experience with it is a reasonable data point. Whether the non-RS and RS variants share identical display compatibility in all configurations is worth a quick check in E-Tube's compatibility chart before @aagedh commits to a purchase.