Home
Forums
New posts
Search forums
User Albums
New media
New comments
Search media
What's new
New posts
New articles
New article comments
Latest activity
Log in
Register
What's new
Search
Search
Search only containers
Search titles only
By:
Latest activity
Register
Menu
Log in
Register
Navigation
Install the app
Install
More options
Change style
Contact us
Close Menu
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Waynemarlow's latest activity
W
Waynemarlow
replied to the thread
Bafang M500 and M600 motors
.
The older DP242 display used to give accurate % right down to 1% for the 52 volts, the newer DP245 doesn't for some reason. On my M510...
Tuesday at 12:33 PM
W
Waynemarlow
replied to the thread
Vitus E-Mythique LT won't power on.
.
Thats pretty normal as long as it’s momentary , it’s just the capacitors loading up.
Friday at 9:27 AM
W
Waynemarlow
replied to the thread
Building a TSA travel friendly 13s1p battery using 18500 cells.
.
Be careful with what appears a very limited knowledge of batteries. Can I suggest perhaps doing quite a bit of research into battery...
Apr 11, 2024
W
Waynemarlow
replied to the thread
Vitus E-Mythique LT won't power on.
.
Does the display register the correct speed when spinning the rear wheel on a stand. I think the motor has to see speed registered to...
Apr 11, 2024
W
Waynemarlow
replied to the thread
Bafang M510 Firmware thread
.
Thanks for the reply Dado. This high cutoff is stopping me using nearly 100Wh of a 800Wh battery. In 3 years the battery technology will...
Apr 9, 2024
W
Waynemarlow
replied to the thread
Bafang M510 Firmware thread
.
I've had a bit of a realisation that the M510 controllers at 52 volts know that it is a 52 volt battery and will shut off the motor at...
Apr 6, 2024
W
Waynemarlow
replied to the thread
M510 motor no support
.
Sounds very Sounds very much like a connector problem, check the usual culprits of the display connectors not being pushed in far...
Mar 22, 2024
W
Waynemarlow
replied to the thread
One day epic in the Pyrenees
.
This guy might be the guy to ask. Bit further on than the French / Spanish border but maybe worth the extra couple of hours driving...
Mar 18, 2024
W
Waynemarlow
replied to the thread
Bafang M560
.
For every rider who hates the over run there are an equal number who ride technical trails that like it. I think your perception that "...
Mar 18, 2024
W
Waynemarlow
replied to the thread
Bafang M500 and M600 motors
.
Thanks. Yes looked at his mods and from my engineering experience, its a good mod but. I've just pulled my M600 engine down and...
Mar 17, 2024
W
Waynemarlow
replied to the thread
Bafang M500 and M600 motors
.
Has anyone found a supplier of the 48mmx 54mmx3mm shaft seal thats on the drive side of the M600 ?
Mar 15, 2024
W
Waynemarlow
replied to the thread
Bafang m510
.
Not actually sure as I bought it in and stuck it on the shelf as a spare as I had eyesight problems with the older DPC242, I'll have a...
Mar 12, 2024
W
Waynemarlow
replied to the thread
Bafang m510
.
Mike, you maybe better looking over on Bafang M500/M600 thread where there are a couple of very knowledgable guys on there ( CiDi for...
Mar 12, 2024
W
Waynemarlow
reacted to
MikeAxles's post
in the thread
Bafang m510
with
Like
.
Hi, I just rolled the dice on a 'dead' e-mythique. Thanks to everyone here for all the information so far, especially @Zimmerframe and...
Mar 12, 2024
W
Waynemarlow
replied to the thread
Vitus E-Mythique LT won't power on.
.
Guys be a little careful with seeing 42 volts on a voltmeter. Although there is volts on the line, there may not be enough current flow...
Mar 12, 2024
Top